Tatamagouche Farmer's Market

Last weekend's gig in Moncton was a great success and I hope to be back there again soon. This coming weekend I am staying closer to home and going to Tatamagouche Farmer's Market on Saturday. It is open from 8am - 12pm at Creamery Square. See you there!

Moncton Market

This Saturday, 19 April 2008, I am setting up my booth at Moncton Market, my first ever show in New Brunswick. Parlez vous Englais, sil vous plait!

It seems to be a very busy place, and I look forward to making lots of new acquaintances there. The hours are 7:00 a.m. – 2:00 p.m. so it's going to be an early start for me, considering that it is a two hour drive. Please excuse me if I'm a bit bleary eyed if you drop by to see me.

The market is the L-shaped red-roofed building in the middle of this map.


View Larger Map

See you on Saturday!

Carving bowl rims

One of the most common questions I get asked about my kitchen-safe bowls is how I make the decoration around the rim. Many think I use a machine, and woodworkers sometimes think I use a chatter tool.

Neither are correct. I use a traditional woodcarving gouge, which when properly sharpened will cut nicely through hardwoods like maple and yellow birch. Normally I have the bowl mounted on the lathe with its outside surface facing me. But the three big bowls that I mentioned earlier today were only ever mounted the other way round, meaning that I had to work from behind the lathe. The easiest way I found to do this is to perch myself on top of the lathe. I felt somewhat like a gargoyle up there, but it gets the job done quite comfortably.

Bowling along

Cyndi left a comment on my last post asking for an update on progress with all those bowls that I am working on. I 'm pleased to say that I have been busy, too busy to blog apparently, and they have now all made it through step two of the process. They have now all had the outside of the bowl turned, sanded and the decoration carved around the rim. Here they are, stacked in boxes in my gallery, the only space I seem to have available at the moment:-

As you can see, there is quite a range of sizes here, from 4" to 17" diameters. So whether you want a bowl to snack on peanuts while you watch tv, or a salad bowl for a big dinner party, I expect to have something soon that will suit your needs.

You have probably noticed that the very small bowls and the two large bowls in the picture above have had their inner surface turned and sanded too, which is the third step in the process. I did all the small bowls one day when I had the lathe set up for another job (a fridge door handle shaped like a rolling pin!) and while the chuck had a small set of jaws installed, I decided to go ahead and turn all the bowls that would need that setup. You see, I like spending my time turning wood, not fiddling with machinery.

The three big bowls had to be dealt with slightly differently in that they were big enough for me to screw them to a faceplate, skipping step one, and doing steps two and three at the same time. Here is the last of the of the big bowls which is on the lathe at the moment, ready for final sanding and carving the rim decoration. It is a whopping 17" diameter and 5" deep, one of the biggest bowls I ever made.

Death row at Seafoam

This month I have been doing little else but turn bowls. I had accumulated over one hundred roughed out bowl blanks and they were beginning to swamp my storage space, so I thought it would be a good idea to take advantage of this quiet time of year to get them turned into finished bowls.

Unfortunately they didn't all make the grade. A couple had split while drying; possibly I had left them too thick, and they weren't able to warp as they dried, and the stress caused them to split apart. Another was an error on my part and the bottom of the bowl was too thin - so thin in fact that it was translucent. So these three bowls ended up on death row:

It is a shame that these bowls didn't make the grade, and I hate to destroy them, but when you consider the total number of bowls that I am working on, I don't consider it a bad loss rate. Some woodturners might salvage these bowls by filling the cracks with epoxy and decorative materials, but most of my customers are looking for practical bowls that can be washed in the sink and will last a lifetime, so I use robust materials and only permit minor defects in the wood.

That is the pile of bowls which I am working on. They have been roughed out and left to dry, and then go back on the lathe four times before they are finished. In the picture above they have all had the first step completed. I have turned a recess on the inside of each bowl's rim. This will allow me to grip the bowl securely in a chuck so that I can shape the outside of the bowl.

I am working on these bowls step by step, putting all of them through step one before moving on to step two. This makes for more efficient working, since each step requires a different set up of the chuck, and a lot of time can be wasted changing the jaws, so while I have it set for one job, that is all I will do, even if it does take a week or more to get through them.